• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer
  • Advertisers
    • Advertise
    • PR Submissions
    • Eblast Submissions
  • Subscribe

Sensor Tips

Sensor Product News, Tips, and learning resources for the Design Engineering Professional.

  • Motion Sensing
  • Vision systems
    • Smart cameras
    • Vision software
    • Lighting
    • Optics
  • Pressure
  • Speed
  • Temperature
  • Suppliers
  • Video
    • EE Videos
    • Teardown Videos
  • EE Learning Center
    • Design Guides
    • Tech Toolboxes

Hall Effect Switch Uses Only Two Wires

May 29, 2014 By Randy Frank Leave a Comment

melexisWith its MLX92242, Melexis Technologies NV Hall effect switch/latch IC can be programmed at the end of a production line to meet the mechanical tolerance requirements of the application. Set via the sensor’s VDD pin, EEPROM programmable memory is used to adjust the various tolerances. Instead of 3-wires, the 2-wire units only use the VDD and GND pins but still provide all the necessary diagnostic capacity to respond if malfunction conditions occur. This saves wiring in in the automotive applications that the sensors target. The sensors operate over a 2.7V to 24V range.

For more information about Melexis MLX92242 Hall effect switch/latch IC, click here.

You might also like

Filed Under: Magnetic sensor Tagged With: Melexis

Reader Interactions

Leave a Reply

You must be logged in to post a comment.

Primary Sidebar

Featured Contributions

Automotive sensor requirements for software-defined vehicles: latency, resolution, and zonal architecture

High-current, low-impedance systems need advanced current sensing technology

A2L refrigerants drive thermal drift concerns in HVAC systems

Integrating MEMS technology into next-gen vehicle safety features

Fire prevention through the Internet

More Featured Contributions

EE TECH TOOLBOX

“ee
Tech Toolbox: Wide Bandgap Semiconductors
Moving from silicon to GaN or SiC feels like a whole new ballgame, doesn’t it? It isn’t just about faster switching; it’s about managing the layout parasitics and thermal realities that come with that speed. This month’s Tech Toolbox features a curated eBook that tackles these design hurdles head-on.

EE LEARNING CENTER

EE Learning Center
“sensor
EXPAND YOUR KNOWLEDGE AND STAY CONNECTED
Get the latest info on technologies, tools and strategies for EE professionals.

RSS feed: Current EDABoard.com discussions Current EDABoard.com discussions

  • Convert Open Collector comparator to PushPull?
  • PNA causality improved significantly reason
  • How to generate ATF34143 transistor layout in ADS2025?
  • SX1262 From Component Selection Pitfalls to a Working LoRa Link
  • What do they connect Y capacitors to in ships?

RSS feed: Current Electro-Tech-Online.com Discussions Current Electro-Tech-Online.com Discussions

  • What if battery is always connected to the charger?
  • Relay terminals
  • Semi-automatic battery handler
  • Coin Battery Case 261104
  • How Can You Identify the Main Causes of Noise in an Analogue Circuit?

EE ENGINEERING TRAINING DAYS

engineering
“bills

RSS feed: Featured White Papers Featured White Papers

  • 4D Imaging Radar: Sensor Supremacy For Sustained L2+ Vehicle Enablement
  • Amphenol RF solutions enable the RF & video signal chains in industrial robots
  • Implementing Position Sensors for Hazardous Areas & Safety

Footer

EE WORLD ONLINE NETWORK

  • 5G Technology World
  • EE World Online
  • Engineers Garage
  • Analog IC Tips
  • Battery Power Tips
  • Connector Tips
  • EDA Board Forums
  • Electro Tech Online Forums
  • EV Engineering
  • Microcontroller Tips
  • Power Electronic Tips
  • Test and Measurement Tips

SENSOR TIPS

  • Subscribe to our newsletter
  • Advertise with us
  • Contact us
  • About us

Copyright © 2026 · Arrowfly LLC and its licensors. All rights reserved.
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Arrowfly.

Privacy Policy